#!/usr/bin/perl
#
# Copyright (C) 1999,2000 Yokogawa Electric Corporation and
# YDC Corporation.
# All rights reserved.
#
# Redistribution and use of this software in source and binary
# forms, with or without modification, are permitted provided that
# the following conditions and disclaimer are agreed and accepted
# by the user:
#
# 1. Redistributions of source code must retain the above copyright
# notice, this list of conditions and the following disclaimer.
#
# 2. Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in
# the documentation and/or other materials provided with
# the distribution.
#
# 3. Neither the names of the copyrighters, the name of the project
# which is related to this software (hereinafter referred to as
# "project") nor the names of the contributors may be used to
# endorse or promote products derived from this software without
# specific prior written permission.
#
# 4. No merchantable use may be permitted without prior written
# notification to the copyrighters.
#
# 5. The copyrighters, the project and the contributors may prohibit
# the use of this software at any time.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHTERS, THE PROJECT AND
# CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING
# BUT NOT LIMITED THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
# FOR A PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT SHALL THE
# COPYRIGHTERS, THE PROJECT OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
# INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
# (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
# SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
# HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
# STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
# IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# POSSIBILITY OF SUCH DAMAGE.
#
# $Id: SAD_a_prm_prb_LLA.seq,v 1.1.1.1 2000/09/28 00:15:46 sekiya Exp $
########################################################################
BEGIN { $V6evalTool::TestVersion = '$Name: $'; }
use V6evalTool;
use icmp;
$IF=Link0;
checkNUT(hostrouter);
#
#
#
vLogHTML("Initialization
");
vCapture($IF);
$ret=makeNCE_TN_LLA();
if( $ret !=0) {
vLog("NUT can not be initialized !!");
exit $V6evalTool::exitFail;
}else {
vLog("*** TN can make TN's link local address NCE in TN ***");
}
#
#
#
vLogHTML("Test
");
vSend($IF, ipv6_tn2nut_unknown_nextheader_LLA);
%ret=vRecv($IF,5,0,0,parameter_problem_nut2tn_LLA_code_1_pointer_fourty);
if( $ret{status} !=0) {
vLog("TN can not receive ICMPv6 error message from NUT");
goto error;
}elsif($ret{recvFrame} eq 'parameter_problem_nut2tn_LLA_code_1_pointer_fourty') {
vLog("TN can receive ICMPv6 Parameter Problem message from NUT");
vLog("OK");
exit $V6evalTool::exitPass;
}else {
vLog("TN receive unexpected packets from NUT");
goto error;
}
error:
vLog("FAIL");
exit $V6evalTool::exitFail;
########################################################################
__END__
=head1 NAME
SAD_a_prm_prb_LLA.seq - check Message Processing Rules (ICMPv6
Destination Unreachable , link local address)
=head1 TARGET
Host and Router
=head1 SYNOPSIS
SAD_a_prm_prb_LLA.seq [-tooloption ...] -p SAD_a_prm_prb_LLA.def
=head1 INITIALIZATION
When test stars, states of Neighbor Cache Entry for TN's
addresses are reachable.
=head1 TEST PROCEDURE
This test verifies that the message processing rule ,
(a) If the message is a response to a message sent to one of the
node's unicast addresses, the Source Address of the reply must
be that same address.
TN NUT
---------------------------
1.
=== IPv6 packet ===>
src address : TN link local address
dst address : NUT link local address
next header is not used in NUT
2.
<< JUDGMENT >>
<=== ICMPv6 Prameter Problem ===
src address : NUT link local address
dst address : TN link local address
Code is 1
Pointer is 40
=head1 JUDGMENT
<< PASS >>
NUT send ICMPv6 ICMPv6 Parameter Problem.
<< FAIL >>
NUT do not send ICMPv6 Parameter Problem.
=head1 SEE ALSO
perldoc V6evalTool
=cut